Hypertherm Duramax Consumables

Powermax45 XP | Powermax65 | Powermax85 | Powermax105 | Powermax125

Genuine Hypertherm Duramax consumables, in stock and shipping NZ wide

Plazmax is an Authorised Hypertherm OEM Channel Partner. We supply Duramax machine torch consumables for Plazmax cutting systems and for any other CNC table, track cutter or robotic cell running a Powermax45 XP, Powermax65, Powermax85, Powermax105 or Powermax125 power source.

This page covers the separate-part consumable stack - electrode, swirl ring, nozzle, retaining cap and shield or deflector. If your torch takes a one-piece SmartSYNC cartridge instead, you have a SYNC system: go to the Powermax SYNC page.

HT technology

Duramax machine torch cutting consumables - Powermax45 XP, 65, 85 and 105

Pick the nozzle by the amperage you cut at, then match the shield to the process. The electrode and retaining cap are the same part right across 45 XP, 65, 85 and 105. The swirl ring is the one part that changes with the power source: 220857 on the Powermax45 XP, 65 and 85, 220994 on the Powermax105.

AmpProcessShield or deflectorRetaining capNozzleElectrodeSwirl ring
45 AShielded220817220854220941220842220857 (220994 on 105)
65 AShielded220817220854220819220842220857 (220994 on 105)
85 AShielded220817220854220816220842220857 (220994 on 105)
105 AShielded220993220854220990220842220994
45 AShielded, ohmic220817220953220941220842220857 (220994 on 105)
65 AShielded, ohmic220817220953220819220842220857 (220994 on 105)
85 AShielded, ohmic220817220953220816220842220857 (220994 on 105)
105 AShielded, ohmic220993220953220990220842220994
45 AUnshielded220955220854220941220842220857 (220994 on 105)
65 AUnshielded220955220854220819220842220857 (220994 on 105)
85 AUnshielded220955220854220816220842220857 (220994 on 105)
105 AUnshielded220955220854220990220842220994

Which rows apply to your machine: a Powermax45 XP runs the 45 A rows only. A Powermax65 runs 45 A and 65 A. A Powermax85 runs 45 A to 85 A. A Powermax105 runs the lot. For the 45 XP, Hypertherm lists the shielded and ohmic sets for the machine torch; the only unshielded set listed for it is the FineCut one in the next table.

Ohmic rows use the ohmic-sensing retaining cap 220953 in place of 220854 so your torch height control can find the plate by contact. Everything else in the stack is the same.

CopperPlus electrode 220777 drops straight into any of these sets in place of 220842. Hypertherm rates it at least twice the life of the standard electrode, for cutting 12 mm and under at 40 A to 105 A. Over 12 mm, stay on 220842.

FineCut, gouging and marking consumables - Duramax machine torch

FineCut is the thin-plate set for mild steel and stainless, with its own nozzle, swirl ring and shield. Gouging and marking sets keep the standard electrode and retaining cap and change the nozzle and shield.

FitsProcessShield or deflectorRetaining capNozzleElectrodeSwirl ring
45 XP, 65, 85, 105FineCut, shielded, ohmic220948220953220930220842220947
45 XP, 65, 85, 105FineCut, unshielded220955220854220930220842220947
65, 85Gouging, Maximum Removal220798220854220797220842220857
105Gouging, Maximum Removal220798220854220991220842220994
65, 85Gouging, Maximum Control420480220854220797220842220857
105Gouging, Maximum Control420480220854220991220842220994
45 XPGouging, Maximum Control 26 to 45 A420480220854420419220842220857
45 XPPrecision gouging 10 to 25 A420414220854420415220842220857
45 XPMarking 10 to 25 A420542220854 or 220953420415220842220857
45 XPHyAccess gouging 65 ANone420413420412420408220857

The FineCut shield 220948 is made to sit on the ohmic cap, so there is no separate standard-cap version of that set. Hypertherm does not recommend FineCut for aluminium.

Gouging: Maximum Removal takes the most metal per pass, Maximum Control gives a narrower, more controllable groove. Both use the same nozzle for a given power source. The 45 XP has its own gouging and marking nozzles at lower current, and the HyAccess set with the extended nozzle and electrode for reaching into corners and over obstructions.

Duramax Hyamp consumables - Powermax125

The Powermax125 runs the Duramax Hyamp torch, and nothing in it crosses over from the smaller Duramax torches. Electrode 220971, retaining cap 220977 and swirl ring 220997 are common to every row below; the nozzle and shield change with amperage and process.

AmpProcessShieldRetaining capNozzleElectrodeSwirl ring
45 AShielded420168220977420158220971220997
65 AShielded420168220977420169220971220997
105 / 125 AShielded220976220977220975220971220997
45 AShielded, ohmic420168420156420158220971220997
65 AShielded, ohmic420168420156420169220971220997
105 / 125 AShielded, ohmic220976420156220975220971220997
-Gouging420112220977420001220971220997
-FineCut, shielded420152220977420151220971220997
-FineCut, shielded, ohmic420152420156420151220971220997

One nozzle and one shield cover both 105 A and 125 A on the Hyamp torch; you do not change parts between the two settings. Hypertherm lists no unshielded set for the Hyamp machine torch.

Compatible setups

These parts are matched to the torch and the power source, not to the table. If your machine runs a Powermax45 XP, Powermax65, Powermax85 or Powermax105 with a Duramax or Duramax Lock machine torch, or a Powermax125 with a Duramax Hyamp machine torch, the tables above are the right parts whatever brand built the gantry, and whether the table came from us or from someone else.

Duramax retrofit torches on older Powermax systems take the same parts. The MRT retrofit machine torch on a Powermax1000, 1250 or 1650 uses the 45 A, 65 A and 85 A shielded, ohmic and unshielded sets from the first table, with the 1650 also running a 100 A set: nozzle 220990, shield 220993 and swirl ring 220994. The MRT2 retrofit torch on a Powermax600, 800 or 900 uses the 45 A sets. Match the amperage to the power source: a Powermax1000 runs 45 A to 65 A, a 1250 runs 45 A to 85 A, a 1650 runs 45 A to 100 A.

The Hyamp machine torch has a 44 mm barrel. If you are fitting a Powermax125 to a track burner, pipe cutter or older table with a 35 mm torch clamp, Hypertherm's Hyamp torch adapter kit 428495 is the mount for it. Ask us, it is not a shop line.

Converting a Duramax torch to cartridges

You can run the one-piece SmartSYNC cartridges in a Duramax torch with a cartridge torch adapter, and then the Powermax SYNC page is your parts list. There are two adapters, and they are not interchangeable:

  • 428951 fits the Duramax Lock torch on a Powermax45 XP and the Duramax torch on a Powermax65, 85 or 105.
  • 528160 fits the Duramax Hyamp torch on a Powermax125.

Two things to know before you order one. The cartridge has no data connection through an adapter, so you do not get the automatic process setup or the cartridge usage tracking that a SYNC system gives you through a SmartSYNC torch; you set amperage and mode yourself, as you do now. And Hypertherm does not recommend the adapter on the Duramax retrofit torches for the Powermax1000, 1250 and 1650. For cut settings with cartridges on a Duramax machine torch, Hypertherm publishes a separate cut chart guide, 811300MU.

Getting the most out of Duramax consumables

Change the electrode on pit depth, not on feel

In machine cutting the electrode usually goes first. Pull it and look at the insert in the tip: once the pit is deeper than 1.6 mm, it is done. Run it past that and it takes the nozzle with it.

A nozzle is finished when the hole is no longer round

Check the centre hole against the light. Out of round or built up with spatter means a wider kerf, more bevel and a cut that wanders. Same check on the shield or deflector, and clear any metal packed between shield and nozzle.

Swirl ring: look at the gas holes, not just the face

A blocked hole or a worn inside surface upsets the gas swirl and shows up as bad cut quality that a new nozzle and electrode will not fix.

Shielded sets can touch the plate, unshielded sets cannot

With unshielded consumables the torch has to be held about 2 mm off the plate and they wear faster than shielded. Shielded is the default for machine cutting unless the job needs the deflector.

Clean, dry air

Oil, water and other contaminants in the air supply shorten consumable life and spoil cut quality. Check the filter element and bowl on the power supply; in a humid shop an air dryer earns its keep.

Pierce height and piercing count

Piercing wears consumables faster than edge starts, and piercing too low sprays molten metal back into the shield and nozzle. Set pierce height from the cut chart and nest to pierce as few times as the parts allow.

Do not run on a continuous pilot arc unless you have to

Continuous pilot arc mode, used for expanded metal and grating, wears consumables noticeably faster. Switch back to normal mode for plate.

A light smear of silicone grease on the torch O-ring

If the O-ring is dry, lubricate it and the threads with a thin layer of silicone lubricant. Worn or damaged, replace it.

FAQs

Take the retaining cap off. If you see a separate electrode, swirl ring and nozzle inside, it is a Duramax torch and this is your page. If one cartridge comes out in your hand, it is a SmartSYNC torch: go to the Powermax SYNC page.
No. The 45 XP is a 45 A machine; fit the 45 A rows only. The other way round is in Hypertherm's own tables: a Powermax85 is listed with the 45 A and 65 A sets, and a Powermax105 with the 45 A, 65 A and 85 A sets, for cutting at those lower currents.
The electrode 220842, the retaining cap 220854, the ohmic cap 220953, the shield 220817, the deflector 220955 and the 45, 65 and 85 A nozzles. The swirl ring is the difference: 220857 on the 45 XP, 65 and 85, 220994 on the 105. Nothing from these torches fits the Powermax125 Hyamp torch.
Only if your torch height control finds the plate by contact (ohmic sensing) before each pierce. If it finds the plate by arc voltage or a mechanical touch-off, the standard cap does the job. Check which your controller is set up for.
For plate 12 mm and under at 40 A to 105 A, Hypertherm rates 220777 at least twice the life of the standard electrode, and it fits in place of 220842 with no other change. Above 12 mm, use the standard electrode.
Yes, with the cartridge torch adapter: 428951 for the Duramax Lock and Duramax torches on a 45 XP, 65, 85 or 105, and 528160 for the Duramax Hyamp torch on a 125. You lose the automatic setup and cartridge tracking that comes with a SmartSYNC torch, and Hypertherm does not recommend the adapter on the retrofit torches for the Powermax1000, 1250 and 1650.
Yes. The parts are matched to the Hypertherm torch and power source, not the table. If it runs a Powermax45 XP, 65, 85, 105 or 125 with a Duramax machine torch, we supply it whoever built the gantry.
No. Hypertherm does not sell consumables or parts direct to end users. It supplies through authorised channel partners and OEMs, and Plazmax is an Authorised Hypertherm OEM Channel Partner. We hold stock and dispatch across New Zealand and Australia.
Most orders ship overnight by express courier from NZ stock.

Request for information

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Name*
This site is protected by reCAPTCHA.
By submitting this form I agree to the Privacy Policy, and that Plazmax may use this information to respond to my enquiry and for marketing and communication purposes.