CNC Plasma Cutting Stainless Steel and Aluminium: Gas, Consumables and Settings

Date

November 13, 2026

Stainless steel and aluminium cut well on a mechanised plasma system, but not with the oxygen process most shops use on mild steel. Hypertherm's cut charts for stainless and aluminium run on nitrogen, F5, nitrogen with a water shield, hydrogen mixes or air, and each of those processes has its own consumable set. Which options you have depends on the power source, and on an XPR system, on the gas console fitted.

This guide covers mechanised Hypertherm XPR, MAXPRO200 and Powermax SYNC systems. It follows Hypertherm's own cut charts and manuals, and the documents are listed at the bottom so you can check them yourself.

What changes when you switch from mild steel

  • The gas. None of the stainless or aluminium cut charts for these systems use oxygen. You will be on nitrogen, F5, a nitrogen and water combination, a hydrogen mix or air, depending on the system and the thickness.
  • The consumables. On XPR and MAXPRO200, every cut chart has its own consumable stack. Changing the gas usually means changing at least some of the parts in the torch. Check the cut chart for the process before you start.
  • The settings. Load the process from the cut chart rather than adjusting a mild steel job. Hypertherm's charts give the cut height, speed, pierce height and pierce delay for each thickness.
  • The grade. Hypertherm develops its stainless HDi cut charts on 304L. Other grades can need small adjustments to get the best cut.

Hypertherm XPR: the gas console decides your options

On an XPR, the gas connect console sets which processes you can run. There are four:

  • Core runs oxygen, nitrogen and air. Hypertherm rates it very good to excellent for angularity and edge finish on stainless up to 12 mm, using the nitrogen HDi process, which keeps air out of the plasma gas for a brighter edge.
  • CorePlus adds argon, for marking and for argon-assisted piercing and severance on thicker plate.
  • VWI (Vented Water Injection) adds F5 gas and water injection, which is what opens up the better stainless and aluminium processes.
  • OptiMix adds three-gas mixing of hydrogen, nitrogen and argon, which gives the most process options on stainless and aluminium.

Each console includes everything the one before it does. Every Plazmax CutAce and CutPro with an XPR comes with the VWI console as standard, and OptiMix is available as an upgrade.

Hypertherm's recommended XPR process by thickness

Thickness Stainless steel Aluminium
1 to 3 mm 40 A nitrogen / nitrogen 40 A air / air
3.5 mm 60 A nitrogen / nitrogen 60 A air / air
5 mm 60 A nitrogen / nitrogen 60 A nitrogen / nitrogen
6 to 10 mm 80 A F5 / nitrogen 80 A nitrogen / water
12 mm 130 A hydrogen mix / nitrogen 130 A nitrogen / water
16 mm 170 A hydrogen mix / nitrogen 170 A nitrogen / water
20 mm 300 A hydrogen mix / nitrogen 170 A nitrogen / water
25 mm 300 A hydrogen mix / nitrogen 300 A nitrogen / water
32 to 50 mm 460 A hydrogen mix / nitrogen 300 A nitrogen / water
64 mm 460 A hydrogen mix / nitrogen 460 A hydrogen mix / nitrogen
75 to 90 mm, edge start 460 A hydrogen mix / nitrogen 460 A hydrogen mix / nitrogen
100 to 130 mm, edge start 460 A hydrogen mix / argon Not recommended

The first gas is the plasma gas and the second is the shield. Here is how that table lines up with the consoles:

  • Nitrogen / nitrogen and air / air run on any XPR console.
  • F5 / nitrogen and nitrogen / water need VWI or OptiMix.
  • Every hydrogen mix process needs OptiMix.
  • The amperage needs the right power source. The 300 A processes need an XPR300 or XPR460, and the 460 A processes need an XPR460.

So on a standard VWI machine, Hypertherm's recommended aluminium processes are covered from 1 mm right up to 50 mm. On stainless above 10 mm, where the table calls for a hydrogen mix, Hypertherm notes that nitrogen with a water shield also gives very good results. Get the pierce technique right with it, because the water's cooling effect can make the molten puddle grow as it solidifies. OptiMix is what you add for the hydrogen mix processes on thicker stainless and the heaviest aluminium.

Quality versus speed

Each XPR process is set up around a core thickness. Hypertherm's advice is to pick the process made for your plate where you can. That gives the best edge and speed with little or no dross. Running a process on plate thicker than it is made for gives square edges with sharp top edges in most cases, but slower speeds, some dross and possibly a darker edge colour on stainless. Running it on thinner plate is faster with a rougher edge. In general, lower amperage gives the better edge and higher amperage gives faster, dross-free cutting.

Hypertherm MAXPRO200

The MAXPRO200 cuts stainless and aluminium with air / air at 50 A, 130 A and 200 A, or with nitrogen / nitrogen at 130 A and 200 A. Hypertherm rates its production cutting capacity, meaning what it will cut at 100% duty cycle, at 22 mm for stainless and 19 mm for aluminium, using the 200 A air process. Maximum pierce is 25 mm on stainless and 32 mm on aluminium, and it will sever up to 63 mm of stainless and 75 mm of aluminium. Severing is for occasional cuts only.

Switching from air to nitrogen at 130 A or 200 A changes the swirl ring and the electrode, and the rest of the stack stays the same. The cut chart for each process shows the full set. Our MAXPRO200 consumables page has Hypertherm's mechanised tables.

Hypertherm Powermax SYNC

A mechanised Powermax65, 85 or 105 SYNC cuts stainless and aluminium with air or nitrogen. It can also run F5, but Hypertherm recommends F5 for stainless steel only. The consumables come as a single cartridge, and these are the rules from Hypertherm's cut chart guide:

  • Standard cutting cartridges at 45 A to 105 A cut mild steel, stainless and aluminium on air.
  • The same standard cartridges cut stainless on F5.
  • FineCut cartridges cut mild steel and stainless on air. Hypertherm does not recommend them for aluminium, or for cutting with F5.

See our mechanised Powermax SYNC consumables for the cartridge range.

Aluminium and water tables

This one matters for safety. Hypertherm warns against cutting aluminium under water or on a water table unless you can stop hydrogen gas building up, because it can explode. Hypertherm also says never to cut under water with hydrogen mix gases or F5. If your table holds water, sort out how hydrogen will be cleared before you cut aluminium on it.

Getting a clean edge on stainless and aluminium

  • Use the process made for your thickness.
  • Load the settings from the cut chart and make small changes with the override or offset functions, not by rewriting the process.
  • Keep your gas clean and dry, at the purity in your system's manual. Poor gas spoils the cut and shortens consumable life.
  • Check the consumables every day. Our guide on how to tell when your consumables are worn covers what to look for.

For where plasma fits against laser and oxy-fuel across different materials and thicknesses, see CNC plasma cutting in NZ.

Consumables and machines in New Zealand

Plazmax is an Authorised Hypertherm OEM Channel Partner. We hold stock of mechanised XPR, MAXPRO200, Powermax and Duramax consumables, dispatched the same business day on most items. Start at our consumables page, or go straight to XPR consumables.

Our CutAce and CutPro CNC plasma cutting systems are designed and built in New Zealand, and every XPR machine comes with the VWI console as standard. Plazmax also services any Hypertherm-powered system in New Zealand, whoever built it, including 24/7 breakdown call-out. See service and support.

Frequently asked questions

Can you plasma cut stainless steel with air?

On a MAXPRO200 or a Powermax SYNC, yes. Both have air cut charts for stainless. On an XPR, Hypertherm's stainless processes use nitrogen, F5, nitrogen with a water shield, or a hydrogen mix, not air.

What gas is best for plasma cutting aluminium?

On an XPR, Hypertherm recommends air at 1 to 3.5 mm, nitrogen at 5 mm, nitrogen with a water shield from 6 mm to 50 mm, and a hydrogen mix from 64 mm. On a MAXPRO200 it is air or nitrogen. On a Powermax SYNC it is air or nitrogen with a standard cartridge.

Do I need different consumables for stainless steel and aluminium?

On XPR and MAXPRO200, each cut chart lists its own consumable set, and changing the gas usually changes some of the parts. On a Powermax SYNC, the standard cartridge covers air on all three metals and F5 on stainless. FineCut cartridges are not recommended for aluminium.

What does the OptiMix console add over VWI?

Three-gas mixing of hydrogen, nitrogen and argon. That unlocks the hydrogen mix processes Hypertherm recommends for stainless from 12 mm and aluminium from 64 mm. VWI already covers F5 and the nitrogen with water shield processes.

Can I cut aluminium on a water table?

Only if you can stop hydrogen gas building up. Hypertherm warns that cutting aluminium under water or on a water table can cause an explosion otherwise.

Which stainless grade are the cut charts based on?

Hypertherm's HDi stainless cut charts are developed on 304L. Other grades can need small adjustments.

Sources: Hypertherm XPR Cut Charts 809830 Revision 9 (process recommendations for stainless steel and aluminium page 22, process selection and categories pages 21 to 23, gas connect consoles page 24, underwater cutting warning page 30, stainless and aluminium cut charts pages 59 to 135); Hypertherm XPR460 Instruction Manual 811530 Revision 0 (gas quality page 49); Hypertherm MAXPRO200 Instruction Manual 807700 Revision 9.4 (cutting capacity page 15, stainless and aluminium cut charts pages 136 to 161); Hypertherm Powermax65/85/105 SYNC Operator Manual 810470 Revision 4.1 (gas types page 23); Hypertherm Powermax45/65/85/105 SYNC Cut Charts Guide 810500MU Revision 4 (cartridge and gas rules and aluminium warning page 6, stainless and aluminium cut charts pages 42 to 70).

Request for information

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Name*
This site is protected by reCAPTCHA.
By submitting this form I agree to the Privacy Policy, and that Plazmax may use this information to respond to my enquiry and for marketing and communication purposes.